Car Simulator Vehicle Signal Generator Automotive Crankshaft Position Hallsensor

Description

Car Signal Generator Vehicle Signal Simulator Automotive Crankshaft Position Hall Sensor Signal Output Simulation 2Hz to 8KHz
Signal Generator Introduction:
This Signal Generator pre-stored all kinds of singals, and can be displayed in LED screen for selection ,no need to download software, Easy to operate.
When the signal generator output is higher than 2HZ, press SET button, it can output 10 types of signal: 60-0 signal is standard magnetoelectric or Hall signal output, other 9 types of signal are magnetoelectric or Hall gear missing teeth signal (Crankshaft position sensor signal).
The Main Key Display:
①LED screen display
②RED Button: Magnetoelectric signal and Hall signal switching
Press down the red button: outputs magnetoelectic signal.
Release the red button: outputs Hall signal.
* For some generators, when press down the red button, it outputs Hall signal, release button, outputs magnetoelectric signal.
* User can use multimeter to check output signal type. Use multimeter (20V measurement) to test the signal generator output, it output is about 5.8V, its output is Hall signal, if output is 0V, the output signal type is Magnetoelectric signal.
③Frequency adjusting Rotation button: Select Frequeny output, ranges: 2Hz-8khz
④12V Power Supply Input
⑤Output signal type selection
⑥Output frequency range selection
⑦12V operationg Power supply socket
⑧PWR-
⑨PWR+
⑩Signal-
⑪Signal+
Main Function:
-Crankshaft position sensor signal output simulation: pre-stored 9 types of gear missing teeth signal: 58+2, 58+1, 57+2, 57+1, 37+1, 36+2, 35+1, 34+2, 22+1 and one type of standard 60+0 signal output simulation.
all type signal above could output in the selection of Magnetoelectric signal or Hall signal
-60+0 signal can simulate vehicle speed sensor signal output.
-60+0 signal can drive odometer or test odometer.
-This Simulator also can simulate ABS sensor, optical sensor signal etc.,
Output Parameters:
One key switch between magnetoelectric signal and Hall signal, convenient to use.
9 channel adjustable frequency,  easy and accurate to select frequency.
-01 represent frequency range :2Hz-1KHz
-02 represent frequency range: 2Hz-2KHz
-03 represent frequency range: 2Hz-3KHz
-04 representfrequency range:  2Hz-4KHz
-05 represent frequency range: 2Hz-5KHz
-06 represent frequency range: 2Hz-6KHz
-07 represent frequency range: 2Hz-7KHz
-08 represent frequency range: 2Hz-8KHz
-09 represent frequency range: 2Hz-100Hz （Driving school mode， low frequency low speed gear）
About Signal Output GND
-If use Hall signal output, signal output GND and the operating power supply GND are in common ground, if use the 12V operating power supply from the battery of the car, user only needs to connect Signal output positive wire.
- If use magnetoelectric signal output, signal output GND and the operating power supply GND are NOT in common ground, user must correctly connect both the output signal positive wire and output signal negative GND wire, thus the signal generator can operate normally.
How to install and use:
About Operating Power Supply Input:
-The operating power supply of that signal generator is 12VDC, user can use the 12V power supply for the Battery of the car, or user any other 12V regulated switching power supply or AC/DC power adapter.
-
Left roatation to the end, adjust output requency to minmum 2Hz, Press SET button, the LED screen display 01, which means output maxmum 1Khz, display 02 means output maxmum 2KHz ..., 08 means output maxmum 8Khz, 09 and above means maxmum 100Hz .
Package List:
1 x Signal generator
1 x Testing Clip